Asus E500-PIB Betriebsanweisung PDF herunterladen (Seite 47)

43 • Schlage • Schlage Utility Soware User's Guide

Controller PropertiesAD-Series Locks and Controllers

WRI400

EDIT Tab (cont.)

Output (PIM400-

TD2)

On Request to Enter:

Active High/Active

Low

Signaled through the PIM400-TD2 to the Access Control Panel, it sets the polarity of

the Request to Enter (RTE) signal.

Active Low

Output (PIM400-

TD2)

On Request to Exit:

Active High/Active

Low

Signaled through the PIM400-TD2 to the Access Control Panel, it sets the polarity of

the Request to Exit (RTX) signal.

Active High

Output (PIM400-

TD2)

On Trouble: Active

High/Active Low

Signaled through the PIM400-TD2 to the Access Control Panel, this sets the polarity

of the Trouble signal.

Active Low

WRI400 - Input

Request to Enter:

Active Open/Active

This sets the polarity of the Request To Enter signal into the WRI400. Default is when

the switch is closed and the WRI400 reads and reports a Request to Enter.

Active Close

WRI400 - Input

Request to Exit: Active

Open/Active Close

This sets the polarity of the Request To Exit signal into the WRI400. Default is when

the switch is closed and the WRI400 reads and reports a Request to Exit.

Active Close

Reader 1 Tamper:

Active Open/Active

Closed

This sets the polarity of the Reader 1 Tamper signal into the WRI400. Default is when

the switch is closed and the WRI400 reads and reports a Reader 1 Tamper.

Active Close

Reader 2 Tamper:

Active Open/Active

Closed

This sets the polarity of the Reader 2 Tamper signal into the WRI400. Default is when

the switch is closed and the WRI400 reads and reports a Reader 2 Tamper.

Active Close

Door Position Switch

(DPS): Active Open/

Active Closed

This sets the polarity of the Door Position Switch (DPS) signal into the WRI400.

Default is when the switch is closed and the WRI400 reads and reports the door

closed.

Active close

First, Delay, Retry First: First query the WRI400 makes to a PIM400 occurs immediately following

presentation of a credential. This parameter is the amount of time, in milliseconds a

WRI400 should wait before making its second query to a PIM400. This setting should

be slightly greater than the fastest response time from the access control panel or

host to any message originated by the WRI400. This optimizes battery life and system

performance.

Delay: The idle time between subsequent queries. Shorter delays may reduce latency,

but also decrease battery life. Longer delays may enhance battery life.

Retry: The maximum number of times the WRI400 queries a PIM400 before it goes

back to sleep. The number of retries should be slightly greater than the longest

response time from the access control panel or host.

Retries = [{Max Response Time of Panel - First}/ Delay] +1

First: 300

msec.

Delay: 200

msec.

Retry: 5 times

Degraded (Cache)

Mode: Full Card

Number or Facility

Code

Use the full card number or the facility codes of previously approved credentials in the

Degraded (Cache) mode.

Full card

number

Degraded (Cache)

Mode: Card Bit

Format

Enter the maximum number of bits in the credential card number.

0 = Degraded (Cache) mode disabled

Degraded (Cache)

Mode: Purge unused

aer 5 days

When enabled, deletes the cache entry aer 5 days of non-use. Disabled

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 86 87

Kommentare zu diesen Handbüchern

Keine Kommentare

Asus E500-PIB Betriebsanweisung Seite 47

Kommentare zu diesen Handbüchern